普通会员

深圳名阀进出口贸易有限公司

进口低温截止阀,进口低温减压阀,进口高压电磁阀,进口蒸汽电磁阀,进口气

产品分类
站内搜索
 
您当前的位置:首页 » 供应产品 » 进口电动衬氟调节阀
进口电动衬氟调节阀
点击图片查看原图
产品: 浏览次数:136进口电动衬氟调节阀 
品牌: 美国威盾
产品口径: DN15-1000
公称压力: 1.6MPA-50MPA
工作温度: 0-180°C
单价: 800.00元/台
最小起订量: 1 台
供货总量: 999 台
发货期限: 自买家付款之日起 3 天内发货
有效期至: 长期有效
最后更新: 2015-11-24 21:38
  询价
详细信息
 进口电动衬氟调节阀

 

一、进口电动衬氟调节阀参数:

公称通径:DN15-300mm

公称压力:PN1.6-2.5Mpa

工作温度:-30℃~+150℃

 

二、进口电动衬氟调节阀简述:

与流体接触的阀体内壁和阀内组件均采用高压注塑工艺,衬有能耐腐蚀、耐老化的聚全氟乙丙烯(F46),又采用聚四氟乙烯波纹管密封。广泛适用于对酸、碱等强腐蚀介质和有毒、易挥发等气体、液体的控制。

Imported electric fluorine-butterfly regulator within the valve body wall and contact with the fluid components adopt high pressure injection molding process, the liner capable of corrosion and ageing resistance of fep (F46), and using ptfe bellows seal. Widely used in strong corrosive medium such as acid, alkali and toxic and volatile gas, liquid control.

三、进口电动衬氟调节阀特点:

1、耐腐蚀:几乎能耐所有的介质(包括浓硝酸和王水)的腐蚀。

2、密封性能好:采用波纹管和填料双重密封,确保无外渗漏。

3、泄漏量小:由于阀芯、阀座采用软密封,故泄漏量低。

4、配用HA执行机构,输出力大、结构紧凑。

 四、进口电动衬氟调节阀安装要求:

1. 管道法兰标准必须与调节阀法兰标准相符。

2. 使用安装前应检查使用条件是否与本阀性能相同。

3. 安装前确认法兰焊接无误,法兰是否冷却。

4. 安装前应先清洗阀门内腔、密封面和管道,不允许有污物杂物附着。

5. 安装时,阀必须与管道对中安装,确保法兰密封面不与管道法兰碰撞等。

6. 本阀最好安装在水平,垂直角度的管道上。

7. 本阀如遇启闭失常,应查明原因,排除故障,不得利用敲、砸、撬和手柄接杆强行启闭。

8. 本阀在贮存未用期间,应保持干燥,不准露天存放,周围不允许有害物质侵蚀。

1, corrosion resistance, can almost all media (including concentrated nitric acid and aqua regia) corrosion.

2, sealed performance is good: the corrugated pipe and double seal packing, ensure no leakage.

3, small leakage: the adoption of soft seal, valve core, valve seat so low leakage.

4, with HA actuators, output force, compact structure.

Imported electric fluorine-butterfly regulating valve installation requirements:

1. The pipe flange standards must be consistent with regulating valve flange standard.

2. Use before installation should check whether the conditions of use and performance of this valve is the same.

3. Before installation, make sure the flange welding, flange is cooling.

4. The body should be clean before installation, sealing face and pipe, there is no dirt sundries clinging to the body.

5. When installation, the valve must be installed in the pipeline to, to ensure the flange sealing surface don't collide with the pipe flange, etc.

6. This valve should be installed best in horizontal and vertical Angle of the line.

7. In case of opening and closing of this valve dysfunction, should find out the reason, troubleshooting, and shall not be used to knock, smashing, pry and handle jaw opening and closing force.

8. The valve during storage unused, should keep dry, not in open air, around does not allow harmful material erosion.

 

 

VTON(威盾)阀门国际有限公司 

 

代理公司:深圳名阀进出口贸易有限公司

联系人:黄生  电话:0755-29172950 传真:0755-29172950

 

使用业绩:

深圳地铁1号线(罗宝线)Shenzhen metro line 1(luobao line)

深圳地铁2号线(蛇口线)Shenzhen metro line 2 (shekou line)

深圳地铁3号线(龙岗线)Shenzhen metro line 3 (longgang line)

深圳地铁4号线(龙华线)Shenzhen metro line 4(longhua line)

深圳地铁5号线(环中线)Shenzhen metro line 5(huanzhong line)

 

 

 

询价单